Due to COVID-19, call volumes are very high and there is no guarantee you will be connected. You can find a lot of great information here on our Help Center, but if you can’t find what you’re looking for we recommend sending us an email and we will respond as soon as we can.

RadCity Rear Wheel Removal Guide

This guide will show you how to remove and reinstall the rear wheel on a RadCity. The photos below show a 2018 RadCity, but the process will be similar for most RadCity models.

Tools Needed:

  • Wooden blocks to prop up the bike
  • Flat side cutters
  • A set of Allen wrenches 
  • 18 mm wrench
  • A camera
  • A torque wrench with a set of Allen bits
  • A few zip ties
  • Nitrile gloves (optional)

Follow the instructions below to remove and reinstall the rear wheel.

Remove the Wheel
  1. Get the bike ready for maintenance. Turn off the bike, remove the battery, press and hold MODE to discharge remaining power.
  2. Shift the bike into 7th gear. Lean the bike on the kickstand, rotate the pedals forwards, and shift the bike into 7th gear so the chain moves to the smallest cog.
  3. Flip over the bike. Set the handlebar grips on the props to protect the LCD display from damage while performing maintenance.

    Flip_the_bike.PNG
  4. Locate and unplug the motor cable. The motor cable is located by the chainstay. Snip zip ties as needed and pull the connector directly apart, without twisting, to unplug.

    Unplug_motor_connector.PNG
  5. Loosen the axle nuts. Use an 18 mm wrench to loosen (but not remove) the axle nuts just enough  so the wheel can be removed. Do not remove the axle nut or washers completely because the orientation of the torque arm and torque washer is very important for safety. 

    Note: 
    We recommend taking a photo of the order of the washers and additional hardware on the motor axle to help with reinstallation.

    Loosen_axle_nuts.PNG
  6. Remove the torque arm bolt. Use an Allen wrench to remove the torque arm bolt.

    Remove_torque_bolt.PNG
  7. Pull the derailleur body toward the back of the bike and remove the wheel. If the rear wheel is difficult to remove, rock the wheel back and forth while lifting, without touching the brake rotor. Lift the chain off of the cog.

    Remove_rear_wheel.gif
  8. Perform necessary maintenance. Once the rear wheel is removed, change the tube or tire, swap in a new wheel, etc.
Reinstall the Wheel
  1. Ensure all hardware is ready to be installed in the correct order. Refer to the images below, which apply to most models, or the photo taken in a previous step.

    Brake rotor side of the wheel:

    Brake_rotor_dropout_view.png

    Derailleur side of the wheel:

    Dropout_view.png
  2. Reinstall the wheel. Pull back on the derailleur body and route the chain onto the smallest cog, then place the wheel in the dropouts.

    Reinstall_the_rear_wheel.gif
  3. Check that the torque washer is in the correct position and the brake rotor is in position. Use the photo taken for reference, if needed. The brake rotor should slide between the brake pads in the brake caliper (1, below), the axle should be fully seated in the dropouts (2, below), and the torque washer should be seated against the freewheel nut with its tab extending into the dropoutIf there is a gap between the axle and the dropout, use a 10 mm wrench to carefully turn the axle to line up the flat sides with the sides of the dropouts, and adjust the wheel so it is fully seated in the dropouts.

    Washer_orientation.png
  4. Install the torque arm bolt. On the brake rotor side, install the torque arm bolt and use an Allen wrench to tighten. Torque the bolt to 5 Nm.

    Remove_torque_bolt.PNG
  5. Tighten the axle nuts. Ensure the axle is seated properly in the dropouts and that the wheel is straight. Tighten the axle nut on the brake rotor side first, then check that the derailleur side is still in place in the dropout. Use an 18 mm wrench to torque both axle nuts to 40 Nm. 

    Loosen_axle_nuts.PNG
  6. Plug in the motor connector. Line up the internal notches and pins (and external arrows), and press each side directly together, without twisting, to reconnect. Replace the zip tie and trim it to be flush and smooth.
  7. Reinstall the battery and test the bike fully before riding.
Caution.png If you are not confident in your ability to successfully and safely perform all steps, we recommend having the work performed or checked by a local, certified, and reputable bike mechanic.

 

Need more assistance?  Submit a request