RadWagon Front Fork Replacement

Watch the video, read through the instructions below, and contact Rad Power Bikes Product Support if you have questions. If you are not confident in your ability to successfully and safely perform all steps, we recommend having the work performed by a local, certified, and reputable bike mechanic.

1. Gather necessary tools and parts: 4 mm Allen wrench, 5 mm Allen wrench, flat side cutters or wire cutters, needle nose pliers, Phillips head screwdriver, the replacement fork from Rad Power Bikes.

2. Power off the bike. Ensure the bike is in the off position and use the key to remove the battery. Once removed, press and hold the “MODE” button on the LCD Display Remote until the display remains off for about two seconds (it may flash on briefly). This ensures the power is fully discharged from the bike and it is safe to work on.

3. Remove the headlight and front fender. Use a 4 mm Allen wrench to remove the bolt holding the headlight and top fender mount to the frame and set aside. Use a 4 mm Allen wrench or Phillips head screwdriver (depending on model year) to remove the bolts holding the fender mounting bracket to each side of the front fork lowers. Pass the fender between the tire and fork to remove and set aside.

4. Remove the front wheel. Open the quick release lever and remove the front wheel from the front fork dropouts.

5. Remove the brake caliper from the front fork. Use a 5 mm Allen wrench to loosen the two bolts holding the caliper to the fork lower and set aside.

6. Remove the brake cable from the caliper. Use a 5 mm Allen wrench to loosen the cable pinch bolt enough to allow the brake cable to slide out of the caliper arm. If there is a cable crimp installed on the end of the cable, use wire cutters to snip off the crimp. Loosen the barrel adjuster and slide the brake cable out of the caliper.

7. Slide the brake cable up and out of the front fork cable guide.

8. Remove the delopilator spring. Use an Allen wrench or screwdriver shaft, perpendicular to the spring, to leverage the spring off of one of the mounting point eyelets and set aside.

9. Remove the top cap and bolt. Use a 5 mm Allen wrench to remove the bolt at the top of the steerer tube.

10. Loosen the steerer tube clamp bolts. Use a 5 mm wrench to loosen the two bolts on the clamp.

11. Remove the steerer tube clamp, handlebar, and spacers from the bike.

12. Remove the front fork from the frame.

13. Install the new front fork to the frame.

14. Install spacers, handlebar, and steerer tube clamp bolts. Use a torque wrench to torque bolts to 10 Nm.

15. Install the bolt and top cap. Thread the bolt into the top of the steerer tube carefully by hand. Use a 5 mm Allen wrench to tighten securely. Install the top cap.

16. Install the deflopilator spring. Hook one end of the deflopilator spring to the eyelet on the downtube of the frame by passing it up from the bottom and through the eyelet. Straddling the bike frame, pass an Allen wrench or screwdriver shaft through the other hook at the end of the spring and leverage the hook onto the front fork eyelet. Keep fingers (and everything) clear of the spring coils during installation.

17. Pass the brake cable through the front fork cable guide.

18. Reinstall the brake cable into the caliper. Pass the cable end down through the top of the barrel adjuster. Pass the cable down through the top of the cable pinch bolt, pull the cable taught, and use a 5 mm Allen wrench to tighten the cable pinch bolt to secure. Slide the cable crimp onto the raw cable end and use needle nose pliers to flatten the crimp to secure.

19. Install the brake caliper to the front fork. Use a 5 mm Allen wrench to tighten the two bolts and secure the caliper to the fork lower.

20. Install the front wheel. Ensure the front wheel quick release is fully open, and lower the fork onto the wheel so the brake disc slides into the caliper and the axle goes into the dropouts fully. Ensure the wheel is centered in the dropouts and fully seated. Tighten the adjustment nut until the quick release lever is held in line with the axle and use the palm of your hand to fully close the lever. Take care to not touch the brake disc.

21. Reinstall the battery, test the bike fully, and have your work inspected by a certified, reputable bike mechanic.

For questions or assistance, contact Rad Power Bikes Product Support by email to support@radpowerbikes.com or by phone to (800) 939-0310 x 2.

 Before using the ebike, always check to ensure all latches, levers, and quick releases are properly secured and undamaged. Check that they are correctly secured before every ride and after every time the bike is left unsupervised, even for a short time. Otherwise, they may come loose and can result in loss of control, damage to the bike, property, serious injury, and/or death.